LeanFind Mode (730/830 used as example below – EDM-700/800 similar.)
The EDM supports two methods of leaning; Rich Of Peak (ROP)and Lean Of Peak(LOP). Note: you can set the power-up default to LOP or ROP in the Pilot Program Mode but easily change modes during flight. During traditional Rich Of Peak leaning, you’ll finalize the mixture to about 20 to 80° rich of peak (depending on engine operating requirements). However, with the advent of closely balanced injectors (such as GAMI), it is possible to set the mixture lean of peak—thus saving fuel and running the engine cooler. Teledyne Continental recommends lean of peak for the Malibu. Both Rich Of Peak and Lean Of Peak processes are described in detail in this manual.
Upon reaching cruise configuration, use the LeanFind mode to identify the correct cylinder to reach peak EGT (for rich of peak this is the FIRST to peak, for lean of peak this is the LAST to peak). To change from one method to the other, just after activating LeanFind, hold STEP and LF and the other method will be momentarily shown: ROP or LOP. Release buttons after other method appears.
The following charts provide step by step guidelines in leaning your engine, for both rich of peak and lean of peak modes:
Lean of Peak leaning is as simple as:
- Pre-lean your mixture.
- Tap the LF button (verify LOP appears).
- Lean mixture until RICHEST flashes (peak found).
- Enrichen to the desired value ‘Lean Of Peak’.
|
L
|
Procedure
|
Scanner Example
|
Comments
|
|
1
|
Establish cruise between 65 to 75% power.
|
|
|
|
2
|
Pre-lean the mixture to 50°F estimated rich of peak on any EGT: _________°F.
|
EGT 1491 CHT 391
|
*See ‘Pre-leaning’
|
|
3
|
Wait one minute
|
|
Let engine stabilize.
|
|
4
|
Tap the LF button
|
LOP
|
Start LeanFind (if ROP appears, hold STEP & LF until LOP appears)
|
|
5
|
Lean the mixture at approx. 10°/secondwithout pausing. (cylinder I.D. box flashes when a EGT rises 15°F)
|
EGT 1520 LF
(Without FF)
– or –
EGT 1520 FF 13.8
(With FF)
|
Flashing cylinder I.D. box identifies the hottest EGT and that an EGT has increased at least 15°F which arms the EDM to now look for first EGT to peak.
|
|
6
|
After the first EGT peaks, you will see LEANESTfor one second and bars coming from the top down. Continue leaning.
|
EGT -17 LF
(Without FF)
– or –
EGT -17 FF 12.4
(With FF)
|
When bars come from the top down, the steady cylinder I.D. box identifies the first EGT that peaked (leanest). Continue leaning.
|
|
7
|
When RICHEST appears, fine tune the delta EGT to the desired degrees below ‘Peak’ (Lean of peak).
|
EGT -45 SET
(Without FF)
– or –
EGT -45 FF 11.6
(With FF)
|
|
8
|
If you hold LF, the peak EGT recorded will be displayed along with FF spread.
|
EGT 1560 PK (Without FF)
– or –
EGT 1560 FF 0.6
(With FF)
|
Captured peak EGT value and if FF equipped, the FF spread between richest and leanest cylinders.
|
LeanFind Procedure—General Explanation
Lycoming and Continental engines have established specific restrictions on leaning that must be followed, such as percentage of power, climb leaning, and TIT limits. Lycoming recommends operation at peak EGT for power settings of 75% or lower, while Continental recommends operation at peak EGT for power settings of 65% or lower. This guide is not meant to supersede any specific recommendations of the engine manufacturer or airframe manufacturer.
It is your responsibility to know your aircraft’s limitations.
Pre-leaning:The leaning process typically begins with ‘pre-leaning’ to insure all cylinders are operating rich of peak EGT (note: you can optionally activate ‘Normalize’ – hold LF untilNRM appears – making it easier to confirm all EGT’s decrease). Now enrichen the mixture to achieve a 50° drop on the hottest EGT. Insure that all EGT’s decrease. Wait one minute to allow temperatures to stabilize.
Lean Find–Initiation: Initiate the EDM leaning mode by tapping the LF button. Note that the EDM displays its current leaning mode momentarily: ‘ROP’ for operating Rich of Peak or ‘LOP’ for operating Lean of Peak. To change, simply hold STEP and LF until the display shows the other mode. The EDM is now waiting for a 15° rise on any EGT (this feature significantly reduces false peaks). Lean the mixture without pausing to achieve about a 10 deg per second change. With a vernier mixture control, turn the knob about a quarter turn every second. With a non-vernier or quadrant mixture control, lean slowly and smoothly about 1/16 inch every five seconds (note: leaning accurately with a quadrant system is difficult due to its mechanical linkage).
Lean Find-Activation: When a 15° EGT rise occurs, LeanFind activates (indicated by a cylinder I.D. box flashing over the number of the hottest EGT). Remember: The LeanFind mode is not active until a cylinder I.D. box is flashing. To show the progress of the leaning process, the EDM now displays the hottest EGT in the left side of the digital display and the word ‘LF’ in the right side (note: with the Fuel Flow option installed, you will see the fuel flow instead of the word ‘LF’). This information allows you to observe the EGT behavior throughout the leaning process.
Lean Find-Lean Of Peak Detection: Note: This mode should only be used when your engine is equipped with balanced fuel injectors. When using the Lean of Peak mode, you lean until all EGT’s decrease slightly below their respective peaks. The EDM has automatic peak detection andwill sequentially indicate leaning progress. When the first EGT peaks, the word LEANEST appears and the cylinder I.D. box highlights the cylinder number. Each column successively drops as leaning continues. When the last column drops (last EGT peaks), RICHEST appears and its respective column flashes momentarily. The last EGT to peak is the one you will use when setting the final mixture.
Lean Find-Finalizing the Lean Of Peak Mixture: The Scanner® Information Area displays the degrees below peak for the last (or richest) EGT to peak, giving you precise information necessary in setting the final mixture. Adjust the mixture to achieve the desired value below peak (using the digital EGT readout) or before engine roughness occurs. Caution: do not lean to the point where the engine runs rough. Note: the peak EGT value encountered during leaning can be recalled by holding the LF button. Tapping STEP exits the lean find mode and automatic scanning resumes.
